How To Change Order Of Monitors Windows 10

On Windows 10, if you lot have a device with more than one network adapter (such as Ethernet and Wi-Fi), each interface receives a priority value automatically based on its network metric, which defines the principal connection that your device will use to send and receive networking traffic.

Although, for the almost part, Windows 10 does a pretty adept job selecting an optimal connection to access the network, sometimes you may need to configure the order of the network adapters manually. For example, if y'all want to use a Wi-Fi over an Ethernet interface when both adapters are connected to the network.

You could disable those adapters y'all don't utilise, but it may not be the best solution as you may need them as backups. Instead, a more straightforward solution is to adjust the interface metric to specify in which social club your device should utilise each network adapter, which you lot can do using Control Panel and PowerShell.

In this Windows 10 guide, we'll walk yous through the steps to modify the network adapter priorities to stay connected using your prefered adapter when using multiple interfaces.

How to modify network adapter priorities using Command Console
How to change network adapter priorities using PowerShell

How to change network adapter priorities using Control Console

If you want to change the social club in which Windows 10 uses network adapters, do the post-obit:

Open up Settings.
Click on Network & Internet.
Click on Condition.
Click the Change Adapter options item.
Right-click the network adapter you lot desire to prioritize, and select Backdrop.
Select the Internet Protocol Version 4 (TCP/IPv4) detail.
Click the Properties push.
In the "General" tab, click the Advanced push.
Articulate the Automated metric option.
In the "Interface metric" field assign a priority value for the adapter.

Quick Tip: The lower the metric number means higher priority, and a higher number indicates lower priority.
Click the OK push button.
Click the OK button again.
Click the Close button.

Once y'all've completed the steps, Windows 10 will prioritize the network traffic depending on your configuration.

The but caveat using the Control Panel feel is that depending on your network setup, you may need to adjust the metric for the Internet Protocol Version six (TCP/IPv6) besides, if that'due south the protocol you're using. (Usually, you will be using the TCP/IPv4 protocol.)

At any time, you can revert the changes using the same instructions, only on step No. nine, make sure to check the Automatic metric option.

How to change network adapter priorities using PowerShell

Alternatively, y'all can change network adapters priorities on a device with multiple interfaces using PowerShell with these steps:

Open First.
Search for Windows PowerShell, correct-click the top result a select Run as administrator.
Type the following command to place the current interface metric and interface index number and printing Enter:

Go-NetIPInterface
Blazon the following command to change the priority gild of the network adapter and printing Enter:

Prepare-NetIPInterface -InterfaceIndex 21 -InterfaceMetric 10

In the control, make sure to change the -InterfaceIndex value to reflect the network adapter y'all want to prioritize and modify the -InterfaceMetric value to assign a priority. Too, think that a lower metric number ways higher priority, and a higher metric number means lower priority.
Type the post-obit command to see the new metric applied to the network adapter and printing Enter:

Get-NetIPInterface

Later completing the steps, Windows ten volition prioritize the network traffic depending on your configuration when multiple network adapters are continued to the network.

At any time, you tin go back to the previous behavior assuasive Windows 10 to decide the network adapter priority using these steps:

Open Start.
Search for Windows PowerShell, correct-click the tiptop result a select Run as administrator.
Type the post-obit control to identify the current interface metric and interface index number and press Enter:

Ready-NetIPInterface -InterfaceIndex 21 -AutomaticMetric enabled

In the command, make certain to alter the -InterfaceIndex value with the correct number of the network adapter you lot desire to use an automated metric.

More than Windows 10 resource

For more helpful manufactures, coverage, and answers to common questions well-nigh Windows 10, visit the following resources:

Windows 10 on Windows Fundamental – All y'all need to know
Windows x help, tips, and tricks
Windows 10 forums on Windows Central